Fiber laser solutions engineered for your application. Request a technical consultation

7-Step Checklist for Setting Up Your xTool S1 Workspace

7 Steps to Get Your xTool S1 Running Without Wasting Two Weeks

I'm the office administrator at a 120-person company. I manage everything from office supplies to workshop equipment — roughly $85,000 in annual purchasing spread across about a dozen vendors. When our design team asked for a laser engraver in early 2024, the job of sourcing, purchasing, and setting it up fell on me.

I didn't know much about laser engravers. I'd handled printing equipment, packaging vendors, and furniture orders. Lasers were new territory. But I applied the same vendor vetting approach I always use and got the xTool S1 20W from a regional distributor with a service contract.

This checklist is what I'd share with anyone doing the same. It assumes you're buying the xTool S1 20W with air assist, the rotary bundle, and the honeycomb panel. Adjust based on your model. The short version: seven steps, roughly three hours of setup labor before you cut anything.

Step 1: Match your laser power to your actual materials before you order

I spent a week comparing the 10W, 20W, and 40W modules before committing. The 10W was about $400 cheaper. The 40W ran $1,000+ more.

The 20W module hit the sweet spot for us. We cut 3mm and 5mm birch plywood for signs, engrave cast acrylic for awards, and mark leather patches for a side project. The 10W would handle the engraving fine, but cutting 5mm plywood would take roughly twice as long with more char along the edges.

If you plan to cut 5mm+ solid wood regularly, the 40W earns its keep. If you're mostly engraving and cutting paper-thin materials, the 10W is fine.

Here's the part nobody tells you: higher wattage is not automatically better for engraving. The 40W module is harder to dial in for fine text on thin material. We tested a 40W loaner before ordering and found that even moderate power settings scorched the edges of 2mm basswood pieces. For fine detail work, the 20W outperformed it. People assume more power equals better output. In practice, more power just means a wider useful range — but a narrower margin for error on delicate jobs.

Step 2: Budget for air assist and honeycomb from day one

The base xTool S1 works without air assist. But after the first week of cutting plywood without it, our workshop lead told me the smoke buildup was making every cut look like it had been done with a cigarette lighter.

Air assist is not optional if you're cutting anything thicker than construction paper. The difference in edge quality and flame control is not subtle. If the vendor offers a bundled price, take it.

The honeycomb panel matters for two reasons. First, it protects your working table. Second, it reduces flashback burn marks on the underside of your material. We didn't order it initially, and the first batch of acrylic awards came out with burn marks on the bottom. We ordered the honeycomb two weeks later.

Step 3: Test every material in your intended lineup before trusting any settings sheet

The xTool software ships with suggested settings for common materials. Don't trust them blindly. Our workshop lead — who spent eight years running a sign shop — told me to ignore them until we tested on our own stock.

The reason: material density varies by supplier. A 5mm sheet from one lumberyard cuts differently from a 5mm sheet from another. Glue content, wood grain, moisture — all of it affects how the laser interacts with the material. We ran a test grid on six materials:

  • 3mm birch plywood from our main supplier
  • 5mm birch plywood from a second supplier
  • 3mm cast acrylic (not extruded)
  • Vegetable-tanned leather, 4oz
  • Anodized aluminum business cards
  • Bamboo cutting boards

Each test grid took about 15 minutes. Six tests, roughly 90 minutes total. That's 90 minutes to avoid the kind of failure that makes you look bad to your team.

Side note: cast acrylic behaves very differently from extruded acrylic. Extruded acrylic cut with the same settings will melt and bubble. Anyone who says "acrylic is acrylic" hasn't tried both.

Step 4: Add the 1064nm infrared module only if you actually need metal marking

The xTool S1 1064nm infrared laser module is a different product from the diode modules. It's designed for marking on metal — not cutting. If your team is thinking about engraving metal tags, branded metal parts, or conductive materials, this is the module that does it.

But here's what I wish someone had told me upfront: it doesn't cut metal. It marks metal. It'll put a clean mark on stainless steel and aluminum. It won't cut through a 2mm steel plate. For that, you need a much bigger industrial machine.

At the time of writing (December 2024), the 1064nm module ran a bit over $600 with the required safety glasses. Whether that's worth it depends on whether your team has a genuine metal-marking use case. In our case, the demand came from engraved stainless nameplates for 5-year employee milestones. That justified the cost.

If you're searching for a "best plasma cutter" or a "lipo laser machine," you're looking at entirely different equipment categories. A plasma cutter is a thermal cutting tool for thick metal, typically operated with industrial power and ventilation. A lipo laser machine is a cosmetic device used in body contouring. Neither has anything to do with precision engraving on thin materials. The S1 with the IR module fills a different niche: fine metal marking for signage, tool tags, and prototype parts.

Step 5: Set up ventilation before the first cut, not after

This is the step most people skip. They fire up the laser, cut a nice test piece, and ten minutes later realize the room smells like burnt wood and they've been breathing it in. Do not do this.

The xTool S1 requires an enclosure or a properly ventilated workspace in almost every commercial setting. The manufacturer's material safety data sheets list the off-gassing profile for each material. Wood and leather are the worst — the fumes are visible and they accumulate.

We installed a 6-inch duct fan venting to the building exterior with flexible aluminum ducting. The exhaust pulls from the top of the enclosure. Total cost was around $180 including the fan, duct, and weather cap. The result: no smell in the room, and the workspace manager stopped complaining.

Check your local fire code and OSHA guidelines before operating. In the U.S., there's no universal rule for a single desktop laser in a commercial workspace, but many fire marshals will require an inspection if you're running it daily. Our insurance provider asked for a photo of the setup and a copy of the material safety data sheets. Keep those on file.

Step 6: Build a settings library before you scale usage

Ninety percent of the value of this machine comes from repeatable output. If everyone who touches the laser has to figure out settings from scratch, you're losing hours every week.

We created a simple shared spreadsheet with four columns: material, thickness, power setting, speed setting. Every time we verify a combination, it goes into the sheet. Six months in, we have about 40 entries. New team members learn from it instead of making the same mistakes.

This is the kind of thing that seems obvious in hindsight but takes two weeks of frustration before someone suggests it. If you're the one setting this up, skip the frustration.

Step 7: Run a five-item safety drill before unsupervised use

Before the machine gets used unsupervised, run a drill with everyone who will touch it. Five items:

  1. Show them where the emergency stop is. Make them physically reach for it.
  2. Show them the fire extinguisher location. Explain that a Class ABC extinguisher is what you want.
  3. Demonstrate what happens when you run a cut without air assist. Do not let them actually do this unsupervised later — but seeing a flame-up once is instructive.
  4. Have them plan a cut, load a material file, run a preview, and confirm settings in the software. No shortcuts.
  5. Read the material safety data sheet for the material they're using and confirm it's on the approved list. PVC is not approved. Anything with chlorine content is not approved.

The drill takes about an hour. It's the difference between "we have a laser engraver" and "we have a laser engraver that hasn't required a fire department visit."

What to watch for (common mistakes)

A few things I wish I'd known before the first month:

  • Focal length changes matter more than the manual suggests. The stock lens handles most needs, but switching between a 2-inch and 4-inch lens changes both the spot size and the optimal focus distance. Re-calibrate the focus z-height after any lens swap.
  • Vector engraving is different from raster engraving. Most first-timers default to raster engraving (filled areas), which is slow and produces visible scan lines. For text and line art, vector mode is faster and cleaner. Figure out how to switch modes before your first real job.
  • The exhaust filter fills up faster than the rating suggests. We replaced our filter after roughly 40 hours of cutting (wood and leather only). The stated capacity is around 60 hours, but the fill rate depends on material. Check it weekly if you're cutting daily.
  • Alignment drift appears after 100+ hours. Not catastrophically, but visible at the edges of large pieces. Check alignment monthly if you're running production work.

None of this is dealbreaking. The xTool S1 has been a solid purchase for us — no vendor drama, no surprise fees, and it's covered the jobs we needed. But the six-month mark is when you start noticing the small stuff. Prepare for it.

One more thing: the manufacturer pushes firmware updates pretty regularly. Check for updates once a month, especially before a big project. We had one update that fixed a Z-axis calibration issue we'd been working around manually. Should have checked sooner.

Jane Smith
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply

Your email address will not be published. Required fields are marked *

Please enter your comment.
Please enter your name.
Please enter a valid email.